常用的螺紋底孔及公差規定(2).docx

《常用的螺紋底孔及公差規定(2).docx》由會員上傳分享，免費在線閱讀，更多相關內容在應用文檔-天天文庫。

1、.常用的螺紋底孔及公差規定常用公制普通螺紋底孔尺寸（JB/GQ0123-80）（單位：mm）公稱粗牙細牙鉆孔直直徑鉆孔直徑螺距鉆孔直徑螺距鉆孔直徑螺距徑M32.6±0.352.7±0.070.05M43.4±3.6±0.070.05//0.54.6±//M54.3-+0.10.050.07M6+0.15+0.155.1-0.050.755.3-0.05M86.8-+00..05157.3-+00..051517.1±0.1M108.6-+00..05159.1-+00..05158.9±0.1M12+0.15+0.151.2510.

2、9±0.11.510.610.3-0.0511.1-0.05+0.15-0.05M1412.1-+00..051513.1-+00..0515M1614.1-+00..101515.1-+00..0515M1815.6-+00..12117.1-+00..0515M2017.6-+00..1219.1-+00..0515M2219.6-+00..1221.1-+00..0515M2421.1-+00..1223.1-+00..0515M3026.6-+00..1329.1-+00..0515M3329.6-+00..1331.6-+

3、00..1232.1-+00..131.5M3634.6-+00..1255°密封圓錐內螺紋底孔尺寸（GB/T7306-1987）公稱直徑鉆孔直徑Rc1/16′6.6-+0.10.05Rc1/8′+0.18.6-0.05Rc1/4′11.5-+00..0515Rc3/8′15-+00..0515Rc1/2′18.7-+00..0515Rc3/4′24.2-+0.20.05Rc1′30.3-+00..12Rc11/4′39-+00..12Rc11/2′44.9-+00..12Rc2′56.7-+00..12Rc21/2′72.4-+0

4、0..121/2”-20UNF10.8-+00..12(12.7)12.6±0.1//14.6±0.116.6±0.116.1-+00..121.518.6±0.118.1-+00..1220.6±0.1220.1-+00..1222.6±0.122.1-+00..1228.6±0.128.1-+00..12////234.1±333.1-+00..120.15常用圓柱管螺紋底孔尺寸（JB/GQ0130-80）公稱直徑鉆孔直徑G1/8′8.8±0.1G1/4′11.7+0.2-0.1G3/8′15.2-+00..12G1/2′19

5、-+00..12G5/8′21-+00..12G3/4′24.5-+0.20.1G1′30.7-+00..1525G1/16′6.7//////;.