資源描述：
《墊片沖裁模畢業論文》由會員上傳分享，免費在線閱讀，更多相關內容在學術論文-天天文庫。
1、目錄§前言任務描述·····································1一.沖壓件工藝性分··································2二.沖壓工藝方案的確定······························2三.主要設計計算····································2（1）排養方式的確定以及計算·······························2（2）沖壓力的計算···················
2、······················2（3）壓力中心的確定及相關計算·····························3（4）工作零件刃口尺寸計算·································3（5）卸料橡膠的設計·······································4四.模具總體設計····································4-13-（1）模具類型的選擇····························
3、···········4（2）定位方式的選擇·······································4（3）卸料，出件方式的選擇·································4（4）導向方式選擇·········································5五.主要零部件設計··································5（1）主要零件的結構設計···································5
4、a.落料凸?！ぁぁぁぁぁぁぁぁぁぁぁぁぁぁぁぁぁぁぁぁぁぁぁぁぁぁぁぁぁぁぁぁぁぁぁぁぁぁぁぁぁぁぁぁぁ?b.沖孔凸?！ぁぁぁぁぁぁぁぁぁぁぁぁぁぁぁぁぁぁぁぁぁぁぁぁぁぁぁぁぁぁぁぁぁぁぁぁぁぁぁぁぁぁぁぁぁ?c.凹模·················································5（2）定位零件的設計·······································6（3）導料板的設計·································
5、········6（4）卸料板部件設計·······································6（5）模架及其他零部件設計·································6六.-13-模具總裝圖······································7七.沖壓設備的選定··································7八.工作零件的加工工藝·····························7九.模具的裝配····
6、·································8十．設計小結·······································9附圖裝配圖········································10（參考文獻）·····························································11沖裁模設計說明書沖裁模設計：根據給定工件圖設計沖裁模具。工件尺寸如圖所示，料厚t=1,材料:紫銅;大批量.-13
7、-要求:1.完成模具總裝圖(3D電子文檔);2.完成總裝配圖,圖紙符合國家制圖標準;3.繪制工程圖,圖紙符合國家制圖標準.4.編寫設計說明書.(A4紙打印)工件圖工件名稱：墊片工件簡圖：如圖所示生產批量：大批量工件材料：紫銅材料厚度：1mm一.沖壓件工藝性分析此工件只有沖孔和落料兩個工序。材料為紫銅，具有良好的沖壓性能，適合沖裁。工件結果簡單，有2個直徑10mm的孔；孔與孔，孔與邊緣之間的距離滿足要求，工件的尺寸全部為自由公差，可看著IT14級，尺寸精度底，普通沖裁就能滿足要求。二.沖壓工藝方案的確
8、定該工件包括落料沖孔兩個基本工序，可有以下三種工藝方案：-13-方案一：先落料，后沖孔。采用單工序模生產。方案二：落料—沖孔復合沖壓。采用復合模生產。方案三：沖孔—落料級進沖壓。采用級進模生產。方案一模具結構簡單，但需要兩道工序兩套模具，成本高而生產效率低，難以滿足大批量生產要求。方案二只需一套模具，工作精度及生產效率都比較高，但制造難度大，并且沖壓成品件留在模具上，清理模具上的物料影響沖壓速度，操作不方便。方案三也只需要一副模具，生產效率高，操作方便，設計簡單，由于
